HardwaxOil

Range of use Suitable for parquet, wood and cork floors. Suitable for virtually all types of European and exotic timber.

Note the LOBA wood types list, which can be found at www.loba.de. If in doubt, consult the factory. Anti-slip as per DIN EN 16165:2021-12 evaluation group R10.

Application From a container size of 10 l the material has to be mechanically stirred for example with LOBA Paint mixer.The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% - 65%, material temperature +18°C - + 25°C, max.

wood moisture 12%, sufficiently ventilate working rooms.In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.Transfer material to a LOBA varnish bucket before applying.Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systemsShake the contents well.Thinner / MixingThe product is ready for use and must not be reduced!

Application tool / application rateTrowel application: LOBA Trowel / approx. 20 ml/m² (50 m²/l) Roller and oilbrush application: LOBA Oil Roller Microfibre 60-80 or LOBA Oil Brush / approx. 40-60 ml/m² (20 m²/l).Drying timeCarefully walkable and recoatable after 8 hours.Light use after 24 hours.Full Stress and coverage after 10 days.The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.Drying times are valid for +20°C and 50% relative humidity.Intermediate sandingWithin 24 hours it can be recoated without, then only with an intermediate sanding.

An intermediate sanding with LOBASAND sanding fleece and underlaid LOBASAND hook & loop strips before the final coat can improve the final visual result.Trowel and roller application:For wooden floors.

Apply HardwaxOil carefully in sections using a LOBA trowel.

Immediately equalise with a single-disc machine and underlaid LOBASAND SpecialPad beige.

Dry minimum 8 hours, maximum 24 hours.

Roll HardwaxOil thinly and evenly with LOBA Oil Roller Microfiber 60-80. For highly absorbent substrates, an additional roll application may be necessary to achieve homogeneous fullness after an intermediate sanding with a LOBA GridPad and hook & loop strips placed underneath.. Roll application:For wooden and cork floors.

Apply HardwaxOil thinly and evenly with the LOBA Oil Roller Microfiber 60-80/LOBA Oil Brush.

Dry minimum 8 hours, maximum 24 hours.

Perform intermediate sanding with a LOBA GridPad and hook & loop strips placed underneath and remove dust.

Apply HardwaxOil thinly and evenly with the LOBA Oil Roller Microfiber 60-80/LOBA Oil Brush. For highly absorbent substrates, an additional roll application may be necessary to achieve homogeneous fullness after an intermediate sanding with a LOBA GridPad and hook & loop strips placed underneath.Suitable product combinationsVersatile color design in combination with:ImpactOil Color Markant Color Follow technical data sheet of the product.Important informationTrowel applications are only possible with joint-sealed wooden flooring. Oil that penetrates joints will not dry completely over a long period.Keep soaked cloths, pads and other tools in closed containers.

Moisten oil in combination with sanding dust, fabric cloths and so on with water or store in a sealable bucket and dispose of in a fire-safe manner, since otherwise there is a risk of self-ignition.